How come Reset/Relearn 4Runner TPMS Light

4 runner 2004-2007 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Initialization is NOT forced if re-inflating tires come the at this time specified tire pressure.

You are watching: 2007 toyota 4runner tire pressure light reset

NOTE: The system will need to be initialized as soon as tires room rotated; tires are changed with tires of different pressures; tire pressure sensor and/or tire pressure monitor ECU are replaced. Collection tire push within the specified selection before initializing. Check out Initializing Tire press Monitor System. Once a tire push sensor and/or tire push monitor ECU space replaced, the sensor ID have to be memorized through the tire push monitor ECU former to system initialization. Check out Tire press Sensor Registration.

Tire push Monitor Warning Light

NOTE: The tire press warning light may turn on as result of natural reasons such as natural air leaks or tires pressure transforms caused through temperature. In this case, adjusting the tire press will turn off the warning light.When the tire push warning light does not go off, or once it come on throughout driving, inspect tire press (including spare tire) and adjust as necessary. The warning light need to turn turn off after a couple of minutes. If the warning irradiate is quiet on even though the tire push is effectively adjusted, the tire can be punctured. Repair as necessary. If the warning irradiate is tho on or blinks, there is a break down in the TPM system. See suitable manufacturer company information.

Under the following conditions, the system may not function properly:

The areas, facilities or tools that use similar radio tide frequencies are located in the vicinity of the vehicle.A radio machine of similar frequency is provided in or close to the vehicle. Together A the majority of snow or ice is grounding to the vehicle, especially the wheels and also around the wheel houses.The battery the the sensor has been depleted. Together A tires without tire pressure monitor valve sub-assembly is used. Tires chains space used.If any other wheels than the mentioned ones room used, the system might not role properly due to the fact that the radio waves are in different ways transmitted from the tire push sensor.Depending top top the tire type, the system may not function properly also though the mentioned wheels are used.

Initializing Tire press Monitor System

NOTE: The mechanism will should be initialized when tires room rotated; tires are changed with tires of different pressures; tire push sensor and/or tire push monitor ECU room replaced; or once a new vehicle is delivered. Set tire pressure within the specified selection before initializing.

NOTE: when initializing the system, the current tire problem is stored together a standard.


During initialization, the tire push monitor valve sub-assembly procedures the inflation push of the tires, and registers the signals that are transmitted into the tire pressure monitor ECU at a frequency of one every 3 minutes. The initialization procedure is completed once the signal from the 5 tires have actually been received.

1. Collection the tire push of all wheels (including spare tire) to pressure specified on the tire and also loading information label.2. Through the auto stopped and also parking brake applied, turn the ignition switch to the ~ above position.3. Press and also hold the tire push warning reset switch until the tire press warning lamp blinks 3 times at one-second intervals.4. Check that initialization is finish using the hand-held tester. Very first select “DATA LIST” ~ above the handheld tester, climate verify that the “TIREPRESS” values are displayed. It might take 5 to 6 minutes for the “TIREPRESS” worths to display screen on the hand-held tester screen

NOTE: The initialization process takes 5 come 6 minute to it is in completed. The initialization process can it is in terminated by connecting terminals 4 (TC) and 13 (CG) of the DLC3.

Tire press Sensor Registration

NOTE: If the tire push sensor and/or tire push monitor ECU room replaced, the transmitter ID requirements to be registered in the tire press monitor ECU former to device initialization. To carry out this procedure, the Toyota hand-held tester have to be used.

Register Transmitter ID

1. Collection the tire push of all wheels (including spare tire) to push specified top top the tire and also loading details label.2. Affix the hand-held tester to DLC3.3. Revolve ignition move to on position.4. Choose the “REGIST TIRE” mode. See Fig. 14 and Fig. 20 .

*
*
5. Intake the transmitter IDs (ID1 to ID5) making use of the hand-held tester and also transmit it come the tire push monitor ECU.6. Collection the identifier transmission problem to “SUCCEEDED”.

NOTE: If procedures 4-6 are not completed within 5 minutes, the setting will return to the normal procedure mode.

Confirmation of Transmitter i would Registration

1. Collection the tire pressure of every wheels (including preventive tire) to the specified value.2. Connect the hand-held tester to DLC3.3. Revolve ignition move to on position.4. Select “DATA LIST” setting on the hand-held tester.5. Confirm the “TIREPRESS” worths are displayed on the hand-held tester screen.

4 jogger 2008-2014 TPMS Reset

TPMS RESET – PROCEDURE

NOTE: Reset is NOT compelled if re-inflating tires to the at this time specified tire pressure.

NOTE: when a tire pressure sensor and/or tire pressure monitor ECU are replaced, the sensor ID must be memorized by the tire press monitor ECU. See Tire

Pressure Sensor Registration.


NOTE: If the an adverse battery terminal is disconnected, initialize the complying with system after the terminal is reconnected: Power home window Control System. Describe owner’s manual or proper manufacturer organization information.

Tire push Monitor Warning Light

When the tire press warning light does no go off, or as soon as it comes on during driving, examine tire press and adjust as necessary. The warning light need to turn turn off within a couple of minutes. If the warning irradiate is quiet on also though the tire pressure is appropriately adjusted, the tire might be punctured. Repair together necessary. If the warning light transforms on within several hrs after adjusting the tires pressure, the tire may have a slow-moving air leak. If the warning light is tho on or blinks, there is a failure in the TPM system. See ideal manufacturer company information.

NOTE: The tire pressure warning light may turn on because of natural reasons such as organic air leaks or tire pressure changes caused by temperature. In this case, adjusting the tire press will turn off the warning light. Under the following conditions, the system may not role properly:

Facilities or devices that use similar radio wave frequencies are situated in the vicinity of the vehicle.A radio an equipment of similar frequency is used close to the vehicle.A most snow or ice cream is stuck to the vehicle, especially about the wheel or wheel housings.Tires and also wheels are installed that space not equipped v a tire push sensor.Snow tires or tire chains room used. Together The battery the the sensor has been depleted.Wheels various other than manufacturer factory wheels are used. If any other wheels than the stated ones are used, the system might not duty properly since the radio tide are in different ways transmitted from the tire pressure sensor.Depending ~ above the tires type, the system may not role properly even though the stated wheels are used. L making use of a different type of tires in mix with real tires.

Tire push Sensor Registration

NOTE: when a tire press sensor and/or tire press monitor ECU are replaced, the sensor ID need to be memorized by the tire press monitor ECU. To carry out this procedure, a Toyota Techstream must be used. That is not important to register the sensor ID(s) as soon as only tire rotation is performed.

NOTE: before beginning registration process on vehicles wherein tire push sensors have not to be replaced, retrieve sensor transmitter ID(s) using intelligent tester or by analysis the identifier on the tire pressure sensor. If sensor is being replaced with a brand-new one, make a note of the transmitter ID prior to installation, as it cannot be checked out after sensor is installed. Watch Fig. 21.

*

1. Collection the tire press of every wheels to pressure specified top top the tire and loading details label.2. Affix the smart tester to DLC3. See Fig. 11.

*
3. Rotate the Tachstream scan device on and also the ignition switch to on position.4. Enter the adhering to menus: Chassis / Tire press Monitor / utility / id Registration.5. Carry out the procedure presented on the scan tool.NOTE: Tire push sensor IDs that were previously registered will be turned off from the memory as soon as registration is completed.6. Check the tire press sensor’s IDs room registered:7. Enter the following menus: Chassis / Tire pressure Monitor / Data List.8. Confirm the tire pressure values are presented for every 4 tires.

NOTE: It may take up to 2 or 3 minute to update the tire pressure data. If tire press values carry out not screen after 2 or 3 minutes, troubleshoot DTCs C2121/21 to C2124/24 (on some models, up to C2125/25).

See more: Where Is Sat Button On Dish Remote "Sat" Button Light, 5 Steps To Fix Dish Remote Sat Button Not Working


NOTE: If the ID(s) have actually not been registered, DTC C2171/71 is set in the tire press monitor ECU ~ 3 minutes or more.