Honda Lug seed Torque Specs, every Models.

You are watching: 2009 honda civic lug nut torque

If you are planning on installing a wheel on your Honda, that is vital to be mindful of the manufacturer"s recommended torque settings. Making use of the proper torque helps ensure that the wheel assembly is securely installed. The Honda Wheel Lug nut Torque Chart we have actually compiled deserve to be offered as a quick reference guide by roadside assistance providers or DIY enthusiasts once working on any type of Honda vehicle.

Using the manufacturer"s recommended torque also helps guarantee the there isn’t either too much or too small pressure on any of the assemblies to which the wheel attaches. Prior to you install her wheels, check your vehicle’s encourage torque.

See more: What Does Knock Sensor Do When Bad Knock Sensor And Replacement Cost

Honda Lug nut Torque Specs Recommendations


MakeModelTrimYear RangeTorque

HONDA

ACCORD - ALLALL / ALL1982 - 201980 ft-lbs
CIVIC - ALLALL / LX1984 - 201980 ft-lbs
CLARITYALL201980 ft-lbs
CROSSTOUR17"BASE / EX2010 - 201580 ft-lbs
CR-VALL / ALL1997 - 201980 ft-lbs
CRXALL / HF1984 - 199180 ft-lbs
CR-Z16"BASE / ALL2011 - 201680 ft-lbs
DEL SOLALL / S1993 - 199780 ft-lbs
ELEMENT2WD / DX/EX2003 - 201180 ft-lbs
EV PLUSALL / HATCHBACK1997 - 199980 ft-lbs
FIT14-INCH / BASE2007 - 201980 ft-lbs
HR-V17"BASE / LX/EX/EX-L2016 - 201980 ft-lbs
INSIGHTALL / ALL2000 - 201980 ft-lbs
ODYSSEYALL / LX/EX1995 - 200480 ft-lbs
ODYSSEYPAX / TOURING2005 - 201995 ft-lbs
PASSPORT2WD / P215/75R151994 - 201995 ft-lbs
PILOTLX/EX / SUV2003 - 200880 ft-lbs
PILOT17"BASE / LX/EX/EX-L2009 - 201590 ft-lbs
PILOT18"BASE / LX/EX/EX-L2016 - 201995 ft-lbs
PRELUDEALL / BASE/SI1985 - 200180 ft-lbs
RIDGELINEALL / RTS/RTL2006 - 201995 ft-lbs
S20002 DOOR / CONVERTBLE2000 - 200980 ft-lbs

Remove or install Front or rear Wheel - share Instructions

When removing and installing a wheel on her vehicle, always follow these generic instructions, yet for much more information please describe your owner"s manual. When lifting your vehicle, make sure you use the ideal equipment and that you just lift the car from the jacking points, one wheel at the time. Always block the opposite wheel from the one you are working on v two wheel chokes ~ above both side of the wheel to avoid the auto from rolling and also fall the the jack when you"re functioning on it. Never gain under the vehicle when the is resting only on the jack.

Always relax the wheel lockable nuts or bolts by hand (use a breaker bar) and also NOT by utilizing an influence drill. Do not jump or usage your foot ~ above the breaker bar.Remove dirt, grease residues and corrosion from rim and wheel hub contact surfaces.Check brake disc retaining bolt for tight fit.Apply anti-seize dough on the wheel centring in the wheel rim.Clean wheel bolts or nuts and also check threads for damage, renew if necessary. Renew corroded wheel bolts. Attention! carry out not apply oil or grease to wheel studs or bolts.The wheel rim should rest uniformly versus the brake disc.Screw in the wheel bolts or lug nuts and also evenly tighten by hand in a crosswise sequence in bespeak to center the wheel rim.Tighten the wheel bolts or lug nuts come the mentioned tightening toque in a crosswise sequence using a calibrated speak wrench.Check every wheel bolts or lug nuts in the same sequence and retighten come the prescribed tightening talk if necessary.Under no circumstances use pneumatic or electric screwdrivers come screw in and tighten the wheel bolts.