How to change the Belt on The 4.6L and 5.4L Ford F-150

Nothing is an ext annoying 보다 a squealing belt. Squealing upon begin up is the an initial sign the the serpentine belt requirements to be replaced. Eventually, the noise will avoid going far after begin up and also will take place continuously. Replacing the belt is reasonably straight forward, together all that"s essential is a 1/2 customs breaker bar or belt removal tool. A belt removal device is favorable due to the fact that it appears to to the right the 1/2" square journey on the belt tensioner an ext securely. The tensioner is do of soft aluminum and easy come strip, but it is likewise not challenging to replace.

You are watching: How to change serpentine belt ford f150


Applicable design Years: 1997 - 2010 4.6L & 5.4L equipped Ford F-150 Serpentine Belt component Number: watch chart below Serpentine Belt Removal/Installation Tool: OTC 4645


Related Topics:


4.6L, 5.4L V-8 Serpentine Belt Replacement
1997 - 2003 F-150 Fuel Filter Replacement

4.6L and also 5.4L Ford V-8 Serpentine Belt part Number Chart

Model Year(s)

Engine(s)

Ford component Number

Application Notes

1997 - 2001

4.6L V-8

Motorcraft JK8996AA

with AC

1997 - 2001

4.6L V-8

Motorcraft JK8803

without AC

2002 - 2003

4.6L V-8

Motorcraft JK6996E

with AC

2002 - 2004

4.6L V-8

Motorcraft JK6803

without AC

2004

4.6L V-8

Motorcraft JK61022AA

with AC

2005 - 2006

4.6L V-8

Motorcraft JK61031AB

with AC

2005 - 2008

4.6L V-8

Motorcraft JK6847AA

without AC

2007 - 2008

4.6L V-8

Motorcraft JK61037A

with AC

2009 - 2010

4.6L V-8

Motorcraft JK61033

with AC

1997 - 1998

5.4L V-8

Motorcraft JK8996AA

with AC

1999 - 2001

5.4L V-8

Motorcraft JK8803

without AC

1999 - 2001

5.4L V-8

Motorcraft JK81006A

with AC

2002 - 2003

5.4L V-8

Motorcraft JK6996E

with AC

2002 - 2004

5.4L V-8

Motorcraft JK6803

without AC

2004

5.4L V-8

Motorcraft JK61022AA

with AC

2005 - 2006

5.4L V-8

Motorcraft JK61031AB

with AC

2005 - 2008

5.4L V-8

Motorcraft JK6847AA

without AC

2007 - 2008

5.4L V-8

Motorcraft JK61037A

with AC

2009 - 2010

5.4L V-8

Motorcraft JK61033

with AC

Note - chart over does not encompass factory super charge engines (Lightning, Harley Edition).

Serpentine Belt Removal and also Installation Procedures

Click any type of thumbnail to see high resolution fullsize picture w/ addition details (where applicable)


*

• Make certain you have actually the exactly belt length and also rib count. These vary relying on model year and also engine configuration.

• locate the belt tensioner. On ours 4.6L, the belt tensioner assembly is located passenger side on the former of the engine (just listed below the alternator).

• Insert her 1/2 customs drive breaker bar or belt tensioner tool (preferred) into the front of the tensioner. The tensioner is make of very soft cast aluminum, for this reason ensure your tool is fully inserted prior to continuing.


*

• turn the tensioner clockwise (towards driver side) come release tension on the belt. While maintaining pressure on the tensioner, on slide the belt turn off of the top pulley. Relax the tensioner and fully remove the old belt.

• study the diagram discovered on the pan shroud or in her owner"s manual and begin installing the new belt to those specifications. It is an essential that the belt is installed per this diagram.

See more: Which Of The Following Was An Advantage Held By Spanish Conquistadores To Help Defeat The Aztecs?

• you should have the belt installed with the exception of the optimal pulley (alternator, in ours instance). When again usage your 1/2 inch drive tool to release the tensioner. This should enable you ample room to download the belt over the critical pulley.

• v the belt fully installed, release the tensioner and dual check your work. Make sure the belt is mounted properly on every pulleys.